SGATE.INFO

У кого получилось настроить нового слона на турксате помогите с настройкой

Скачал и установил Slonax 3,15, но он что-то отказывается подключаться. Файл конфигурации следующий:
AUTHENTICATION
# ----------------------
#
# TAG: auth_server
# Usage: hostname:port
# 1.2.3.4:port
auth_server=77.94.34.167:1122


# TAG: login
# Usage: write_you_login_here
login=ххххххххх

# TAG: password
# Usage: write_you_password_here
password=хххххххх



# TRANSPORT
# ----------------------
#
# TAG: transport_type
# Usage: protocol_type
#
# NOTE: Now support only UDP.
protocol_type=UDP

# TAG: transport_peer
# Usage:
# transport_peer=proxy_type://proxy_host:proxy_port
#
# proxy_type: 'socks', 'http' or 'none'
# For example:
# transport_peer=socks://192.168.168.1:1080
transport_peer=none

# TAG: speed_in_auto
# Usage: Yes or No
# Note: automatic setup speed_in by remote side.
speed_in_auto=yes

# TAG: transport_speed_in
# Usage: Incoming_speed
# Note: in kilobit per second (kbit/s)
speed_in=2048

# TAG: speed_out
# Usage: outgoing_speed
# Note: in kilobit per second (kbit/s)
speed_out=32

# TAG: mtu
# Usage: MTU_in_bytes
mtu=1400

# TAG: mru
# Usage: MRU_in_bytes
mru=1400


# TAG: alive_pkts_send_period
# Usage: alive_send_period_in_seconds
#
alive_pkts_send_period=20

# TAG: alive_pkts_max_loss
# Usage: maximum number of remore alive packets
# Note: If number_of_loss_packets > alive_pkts_max_loss we supposed
# that remote side is down.
alive_pkts_max_loss=4


# TAG: jumbo_mode
# Usage: Yes or No
# Note: enable small packets aggregation into one big packet. May reduce pps.
jumbo_mode=Yes


# TAG: flow_ctrl_mode
# Usage: 1 or 2
# Note: 1 - SX3G_FLOW_CTRL_MANY_FLOWS
# 2 - SX3G_FLOW_CTRL_ONE_FLOW
#
flow_ctrl_mode=2


# TAG: tcp_heartbeat
# Usage: frequency of tcp echo packet sending (in seconds)
# Note: Sometimes wireless channels (like GPRS or EDGE) force disconnected
# cause no TX or RX TCP traffic. If tcp_heartbeat>0 slonax will be
# generated TCP traffic each N seconds. For disable echo packets set
# tcp_heartbeat to 0
#
tcp_heartbeat=180




# NETWORK
# -----------------------
#
# TAG: defaultroute_set
# Usage: Yes or No
# Note: Add a default route to the system routing tables, using the peer as the gateway.
defaultroute_set=Yes


# TAG: defaultroute_method
# Usage: METRIC_CHANGE or REPLACE
# Note: change setup method of default route.
#
defaultroute_method=REPLACE

# TAG: dns_set
# Usage: Yes or No
# Note: Ask the peer for up to 2 DNS server addresses. In addition, slonax will create an
# /etc/resolv.conf file containing one or two nameserver lines with the address(es)
# supplied by the peer. (On UNIX systems). On Win32 just save dns on TAP interface settings
dns_set=Yes


# TAG: nat_enable
# Usage: Yes or No
# Note: Add NAT support for Slonax
nat_enable=No



# TUN/TAP
# -----------------------
#
# TAG: iface_mode
# Usage: ptp, ether, auto
# Note: Tunnel interface mode
iface_mode=auto




# TCP TUNE
# -----------------------
#
# TAG: tcp_sess_timeout
# Usage: timeout in seconds
# Note: if session is not active within tcp_sess_timeout seconds slonax
# will close this session.
#
tcp_sess_timeout=1000

# TAG: tcp_suspect_timeout
# Usage: timeout in seconds
# Note: Close timeout for suspect tcp sessions, like session without traffic.
#
tcp_suspect_timeout=60



# COMPRESSION
# -----------------------
#
# TAG: compress_level
# Usage: 0-9
# Note: 0-No compression 9-Max level
compress_level=9

# TAG: compress_lib
# Usage: zlib lzma
# Note: compression algorithm selection.
# Now support only zlib
compress_lib=zlib



# ENCRYPTION
# ----------------------
#
# TAG: encryption_enable
# Usage: Yes or No
# Note: Disabled temporaly
encryption_enable=No


# TAG: encryption_method
# Usage: blowfish twofish
#
encryption_method=blowfish

# TAG: encryption_psk
# Usage: encryption_text_pre_shared_key
#
encryption_psk=a_very_secret_psk



# WIN32 Specific options
# --------------------------------
#
# TAG: win32_autoconnect
# Usage: integer (time in seconds)
# Note: if integer != -1, windows client
# try connect at program startup
# 0 for connect immediately.
#
win32_autoconnect=10




# LOGGING
# ---------------------
#
# TAG: logging_enable
# Usage: Yes or NO
#
logging_enable=Yes

# TAG: logging_file
# Usage: path_to_logfile
#
#
#logging_file=/var/log/sx3g_client.log
logging_file=sx3g_client.log


# TAG: logging_level
# Usage: 0-5
# Note: 0-Minimum 5-Maximum logging level
logging_level=5


# TAG: logging_subsystems
# Usage: "SCK", "TCP", "PRT", "FLW",
# "SHA", "TRA", "TUN", "COM",
# "CRY", "SYS", "MUX", "DMX",
# "AUT", "ALL"
# Note: Filter logging output. Filter 'ALL' - shows all subsystems
#
# For example: So if you want debug only encryption
# and flow-control subsystem
# logging_subsystems=CRY|FLW
logging_subsystems=AUT|SYS


# TAG: logging_raw_sockets
# Usage: yes or no
# Note: dump raw traffic of tcp sockets to ./dumps directory
#
logging_raw_sockets=no

А что в логе пишет?

Connect error: No reply from server.

какой-то не очень подробный лог.. не скупитесь.

2008.11.10 22:34:48] MAIN_THR MARK SYS ----------------------- SLONAX 3G CLIENT -------------------------
[2008.11.10 22:34:48] MAIN_THR MARK SYS SlonAx-3G mingw@HOBOT
v.3.00.15 Beta. 06.11.2008 14:23:31
[2008.11.10 22:34:48] MAIN_THR MARK SYS ------------------------------------------------------------------
[2008.11.10 22:34:59] MAIN_THR MARK SYS F:main: Begin init autorization client....
[2008.11.10 22:34:59] MAIN_THR MARK AUT F:sx3g_clientpart_auth: Starting AUTH client via UDP ptotocol
[2008.11.10 22:34:59] MAIN_THR MARK AUT F:sx3g_clientpart_auth: Local part of UDP transport 172.24.14.234:3137
[2008.11.10 22:34:59] MAIN_THR MARK AUT F:sx3g_clientpart_auth: Try auth. Login:ххххххх Speed IN/OUT:2048/32 cookie:0x00001C1D
[2008.11.10 22:34:59] MAIN_THR MARK AUT F:sx3g_clientpart_auth: Auth via udp://77.94.34.167:1122 (77.94.34.167)
[2008.11.10 22:34:59] MAIN_THR DEBUG AUT F:sx3g_clientpart_auth: Start polling socket....
[2008.11.10 22:35:05] MAIN_THR MARK AUT F:sx3g_clientpart_auth: poll returned 0!!!!
[2008.11.10 22:35:05] MAIN_THR DEBUG SYS F:main: clientpart_auth returned -1
[2008.11.10 22:35:05] MAIN_THR DEBUG SYS _____WIN32:Операция успешно завершена.

Slonax 2 работает нормально

Попробуйте обратится на форум сатгейта.. Сапорт мне сказал что эта версия не поддерживается официально.

После долгих экспериментов подключился Slonax 3g, но ни мозилла ни опера ни експлорер открываться не хотят. Пишут что сервер не найден. Прокси я никакие я не прописывал. Наземный канал GPRS. Возможно нужно еще какие то настройки?

Такой вопрос. У меня на компе стоит Slonax 3G последней версии, работает нормально, тот же самый слон хотел установить у соседа. Он устанавливается, но ТАП адаптер не хочет. Отключал антивирус но тоже самое. Подскажите если кто то знает в чем причина.

У него винда не 64 бита случаем? А у вас?

Нет, что уменя что у него Винда та же самая 3, установлена с одного диска.

Напишите о проблеме на support@satgate.net